Journal of Quality Engineering and Management

Providing a comprehensive model to define the technical requirements of complex systems in design offices

Document Type : Original Article

Authors

Sadegh Fazel 1
Jafar Boostanpoor 2
Ali Abbasi 3

1 Phd from ferdowsi university of mashhad

2 phd from ferdowsi university of mashhad

3 Msc from azad university of mashhad

https://doi.org/10.48313/jqem.2024.210888
Abstract
In this paper, firstly, a comprehensive and detailed model is presented to define the technical design requirements of engineering systems to be designed in design offices. From a theoretical point of view, it has been tried that the proposed model includes the general categories of technical requirements presented in international and national standards, as well as important references in the field of system engineering. From a practical point of view, the presentation of this model is based on the practical experience of defining the technical requirements for the design of a variety and a large number of complex electrical, electronic, computer, telecommunication, mechanical, and electromechanical systems. Also, as an example in this paper, the results of the definition of technical requirements for a type of Global Maritime Distress and Safety System, GMDSS, as one of the essential telecommunication subsystems of a type of surface vessel according to the proposed model, are briefly presented. Therefore, the proposed model can be used to define the technical requirements of a wide range of engineering systems in design offices.

Keywords

Technical Requirements
Stakeholder expectation
System engineering
Design office
Telecommunication system
  1. INCOSE, 2023, "Systems engineering handbook- A Guide for System Life Cycle Processes and Activities", Fifth edition, International Council On Systems engineering, Wiley.
  2. Eisner, H., 2022, "Tomorrow's Systems Engineering: Commentaries on the Profession". United States: CRC Press.
  3. Eisner, H., 2022, "Systems Engineering: Building Successful Systems", Poland: Springer International Publishing.
  4. Kossiakoff, , Biemer, S. M., Seymour, S. J., Flanigan, D. A., (2020), "Systems Engineering Principles and Practice", United States: Wiley.
  5. Hosseini Mones, Seyed Ahmad, Kia, Ali, 2016, "Engineering
  6. ISO/IEC/IEEE 15288:2023, 2023, Systems and software engineering, System life cycle processes.
  7. ISO/IEC/IEEE Draft International Standard - Systems and software engineering -Life cycle management - Part 2: Guidelines for the application of ISO/IEC/IEEE 15288, 2023.
  8. ISO/IEC/IEEE 24748-7000:2022, 2022, Systems and software engineering, - System life cycle processes, Standard model process for addressing ethical concerns during system design.
  9. Systems and software engineering, System life cycle processes, project management".
  10. NASA systems engineering handbook", Rev2.
  11. NASA, 2017, "Guide to NASA systems engineering handbook", 2017.
  12. NASA/SP-2007-6105, 2007, "NASA systems engineering handbook", Rev1
  13. MIL-STD 498, 1994, "Software systems engineering draft", Department of Defense (DOD).
  14. MIL-STD 499B, 1993, "Systems engineering draft", Department of Defense (DOD).
  15. DOD Instruction 5000.2., 2008, "Operation of the defense acquisition systems", Department of Defense (DOD).
  16. ANSI/EIA-632A, 2021, "Processes for engineering a system".
  17. INSO-13288, 1400, "Systems and Software Engineering - Life Cycle Processes - Project Management", National Defense Standards Organization of Iran, Tehran.
  18. Systems Engineering Guidelines", Iranian Defense Standards Center, Tehran, 2012, IDS1315
  19. Systems Engineering and Systems Engineering Processes
  20. IDS1107, 2011, "Idea Realization Process Architecture (Idea to Prototype) - General Requirements", Iranian Defense Standards Center, Tehran.
  21. Engel. A., 2010, "Verification, Validation and testing of engineered systems", Jhon whiley & Sons.
  22. Fazel, Sadegh, Bustanpour, Jafar, December 1402, "Presenting a comprehensive model for designing verification, validation, and testing procedures for complex systems in design offices", Second Conference on Quality and Reliability Management and Engineering, Malek Ashtar University of Technology.
  23. Fazel, Sadegh, 2009, "Error and Hazard Analysis and Control from the Perspective of Reliability and Safety - Theory and Practice", Tehran, Sarvnegar Publications.
  24. ISO-31000, 2018, "Risk management– Principles and guidelines", International Organization for Standardization, Geneva,Switzerland.
  25. AIAG & VDA, 2022, " FMEA Handbook, Potential Failure Mode and Effect Analysis", AIAG & VDA Groups, First Edition.
  26. AIAG Group, 2008, "Potential Failure Mode and Effect Analysis", Chrysler Corporation and Ford Company and General Motors Corporation, Fourth Edition.
  27. E. A., 2012, "Reliability Engineering", Addison Wesley Longman.
  28. A., 2012, "Reliability Engineering- Theory and Practice", Springer, Fourth Edition.
  29. Fazel, Sadegh, 2014, "Reliability Engineering - Predictive Methods - Theory and Practice", Tehran, Daneshnegar Publications.
  30. C. A., 2015, "Hazard analysis techniques for system safety", Second edition, John Wiley & Sons.
  31. MIL-STD-882E, 2012, "Department of defense standard practice for system safety", US Department of Defense (DOD).
  32. Fazel, Sadegh, 2019, "Safe control of the trajectory of surface vessels based on the risk/threat index", Ferdowsi University of Mashhad.

 

Home

Editorial Board

Indexing and Abstracting

Guide for Authors

Submit Manuscript

Reviewers

Contact Us